10Gbps SFP+ SR Module | Universal Compatibility with Cisco/HP/Huawei/H3C/Netgear/Ubiquiti/Mikrotik - Shenzhen Whandar Optical Technology Co., Ltd.

Home > Products > Optical Transceivers > 10G SFP+ Module

View large

SFP-10G-SR 10G SFP+ SR 850nm 300m LC MMF DDM Fiber Optical Transceiver Module

Duplex SFP+ MMF Transceiver
Hot Pluggable
LC connector receptacle
Optical interface compliant to IEEE 802.3ae
Electrical interface compliant to SFF-8431

Specification

Features

ü Hot-pluggable SFP footprint

ü Duplex LC fiber connector

ü Transmission distance up to 300m on 50/125µm or 62.5/125µm MMF

ü Built-in DDMI functions

ü Comply with SFP MSA .

ü Single +3.3V power supply

ü RoHS6 compliant (lead free)

ü Operating case temperature:

Commercial : 0 to +70°C

Industrial : -40 to +85°C

ü Comply with Ethernet Switches from a lot of widely used brands .

Applications

ü 10GBASE Ethernet

ü STM-64 / SONET OC-192 SDH STM-64

ü Switch to Switch interface

ü Router/Server interface

ü Other optical transmission systems

Optical Characteristics

Optical transmitter Characteristics
Parameter	Symbol	Min	Typical	Max	Unit	Notes
Launched Power (avg.)	POUT	-7.3		-1	dBm
Optical Power OMA	POMA		-1.5		dBm	1
Operating Wavelength Range	λC	840	850	860	nm
Spectral Width (RMS)	∆λ			0.45	nm
Extinction Ratio	ER	3			dB	2
Transmitter and Dispersion Penalty	TDP			3.2	dB
Optical Output Power after TX Disable	PDIS			-30	dBm
Relative Intensity Noise	RIN			-128	dB/Hz
Optical Return Loss Tolerance	ORL			12	dB
Tx Jitter	Txj	Per IEEE 802.3ae requirements
Optical Receiver Characteristics
Parameter	Symbol	Min	Typical	Max	Unit	Notes
Wavelength Range	λC	840	850	860	nm
Receiver Sensitivity (OMA)	RSENS1			-11.1	dBm	3
Stressed Receiver Sensitivity (OMA)	RSENS2			-7.5	dBm	3
Optical Power Input Overload	Pin-max	+0.5			dBm
LOS De-Assert	LOSD			-13	dBm	3
LOS Assert	LOSA	-30			dBm	3
LOS Hysteresis		0.5			dB	4
Receiver Reflectance	Rr			-12	dB

Notes:

1. Per Tradeoff Table 52.8, IEEE 802.3ae 2005

2. For the measurements, the device was driven with 231-1 PRBS pattern.

3. Measured with a PRBS 231-1 test pattern, @10.3125Gbps,, BER<10-12

4. The LOS Hysteresis minimizes ‘chatter’ on the output line. In principle, Hysteresis alone does not guarantee chatter-free operation.

Pin definition

The SFP+ modules are hot-pluggable. Hot pluggable refers to plugging in or unplugging a module while the host board is powered. The SFP+ host connector is a 0.8 mm pitch 20 position right angle improved connector specified by SFF-8431, or stacked connector with equivalent electrical performance. SFP+ module contacts mates with the host in the order of ground, power, followed by signal as illustrated by Figure 1 and the contact sequence order listed in Table 1.

Figure 1 SFP+ Pad Assignment Top View

Pin No	Symbol	Name/Description	Power Seq.	Note
1	VeeT	Transmitter Ground	1st	1
2	TX_Fault	Transmitter Fault	3rd	2
3	TX_Disable	Transmitter Disable	3rd	3
4	SDA	2-Wire Serial Interface Data Line	3rd	4
5	SCL	2-Wire Serial Interface Data Line	3rd	4
6	Mod_ABS	Module Absent, Connect to VeeT or VeeR in Module	3rd	5
7	RS0	No connection required	3rd	6
8	RX_LOS	Receiver Loss of Signal indication	3rd	7
9	RS1	No connection required	3rd	8
10	VeeR	Receiver Ground	1st	1
11	VeeR	Receiver Ground	1st	1
12	RD-	Receiver Inverted DATA out. AC Coupled. CML-O	3rd	9
13	RD+	Receiver Non-inverted DATA out. AC Coupled. CML-O	3rd	9
14	VeeR	Receiver Ground	1st	1
15	VccR	Receiver Power Supply	2nd	10
16	VccT	Transmitter Power Supply	2nd	10
17	VeeT	Transmitter Ground	1st	1
18	TD+	Transmitter Non-Inverted DATA in. AC Coupled. CML-I	3rd	11
19	TD-	Transmitter Inverted DATA in. AC Coupled. CML-I	3rd	11
20	VeeT	Transmitter Ground	1st	1

Power Seq.: Pin engagement sequence during hot plugging.

Notes:

1. The module signal ground contacts.

2. This pin is an open drain/collector and should be pulled up to Vcc-host in the host with a 4.7k~10k Ohm resistor.

3. This pin should be pulled up to VccT with a 4.7k~10k Ohm resistor in modules.

4. SDA&SCL (IIC) are needed pull up 4.7k~10k Ohm resistors on host board.

5. Mod_ABS is connected to VeeT or VeeR in the SFP+ module.

6. Rate Select 0, no connection required.

7. Module RX_Los of signal indication need pull up 4.7k~10k Ohm resistor on host board.

8. Rate Select 1, no connection required.

9. RD -/+: These are the differential receiver outputs. They are CML AC-coupled with 100 Ohm terminal resistor matching internal.

10. VccR and VccT are the receiver and transmitter power supplies.

11. TD-/+: These are the differential transmitter inputs. They are CML AC-coupled with 100 Ohm terminal resistor matching internal.

Ordering information

PART NO.	Specifications
	Pack	Rate	Tx	Po	Sen	Temp	Reach	DDM
	Pack	(Gbps)	(nm)	(dBm)	(dBm)	(℃)	(m)	DDM
HD-SFP+/10G-SR	SFP+	10.3125	850	-7.3~-1	＜-11.1	0~70	300	Y

*Note：

1. Measured with a PRBS 231-1 test pattern, @10.3125Gb/s.

2. More detail product selection and cable lengths, please contact Handar.

Need Help? Contact Our Product Experts or Sales Team Today!

Latest News & Blog

: 2025-08-05 Application and Advantages of 1×9 Optical Transceivers in Industrial Printing Systems
As industrial automation and smart manufacturing continue to evolve, communication systems within industrial printing equipment are shifting from traditional copper-based connections to more reliable fiber-optic solutions. Among various optical transmissi

: 2025-08-05 Application of Optical Modules in Mesh Network Topology
Consider employing a mesh network topology to meet your communication and data transmission needs. In this article, we will focus on the application of optical modules in mesh networks to help you better understand this critical technology. 1. High-Speed

: 2025-08-05 Unlocking the Future of Connectivity with OTN Technology
In todays rapidly evolving digital landscape, the need for reliable and efficient data transmission has never been more crucial. Enter Optical Transport Networks (OTN), a technology that is poised to revolutionize the way we connect and communicate. In th