Contact Us 中文
Home > Products > 40G/100G Module > 40G QSFP+ Module

QSFP-40G-SR4 40G QSFP+ SR4 850nm 150m MTP/MPO MMF DDM Transceiver Module

Maximum link length of 100m on OM3 MMF and 150m on OM4 MMF

Features

◆ Hot Pluggable QSFP+ form factor

◆ Supports 41.25Gb/s aggregate bit rate

◆ Multi rate capability: 1.06Gb/s to 10.5Gb/s per channel

◆ Maximum link length of 100m on OM3 MMF and 150m on OM4 MMF

◆ Single MPO-12 receptacle

◆ Power dissipation: <1.5 W

◆ Single 3.3V power supply

◆ Built-in DDMI functions

◆ Commercial case temperature range of 0°C to 70°C

◆ RoHS 6 Compliant

 

Applications

◆ 40GBASE-SR4 40G Ethernet

◆ 40G-IB-QDR /20G-IB-DDR / 10G-IB-SDR InfniBand

◆ Breakout to 4 x 10GBASE-SR

◆ Proprietary interconnections

 

Optical Transmitter Characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Center Wavelength

λout

840

850

860

nm


Average Launch Power each

lane

Pout

-7.6


2.4

dBm


Difference in Power between

any two lanes [OMA]

DPX



4.0

dB


Peak Power per Lane

PPX



4.0

dBm


Spectral Width (RMS)

σ



0.65

nm


Optical Extinction Ratio

ER

3.0



dB


Transmitter and Dispersion

Penalty each lane

TDP



3.5

dB


Optical Return Loss Tolerance

ORL



12

dB


Average launch power of OFF

transmitter, per lane




-30

dBm


Transmitter eye mask

definition{X1,X2,X3,Y1,Y2,Y3}

{0.23,0.34,0.43,0.27,0.35,0.4}


Optical Receiver Characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Receiver Wavelength

λin

840


860

nm


Average Receive Power per

Lane

RXPx

-9.5


2.4

dBm


Stressed Receiver Sensitivity in

OMA

SRS



-5.4

dBm

1

LOS Assert

LOSA

-30



dBm


LOS De-Assert

LOSD



-12

dBm


LOS Hysteresis


0.5



dB


Receiver Reflectance

Rfl



-12

dB


Notes:

1.Measured with a PRBS 231-1 test pattern, @10.3125Gb/s, BER<1E-12.


Pin Assignment

 

Pin

Symbol

Name/Description

Notes

1

GND

Transmitter Ground

1

2

Tx2n

Transmitter Inverted Data Input


3

Tx2p

Transmitter Non-Inverted Data output


4

GND

Transmitter Ground

1

5

Tx4n

Transmitter Inverted Data Input


6

Tx4p

Transmitter Non-Inverted Data output


7

GND

Transmitter Ground

1

8

ModSelL

Module Select


9

ResetL

Module Reset


10

VccRx

3.3V Power Supply Receiver

2

11

SCL

2-Wire serial Interface Clock


12

SDA

2-Wire serial Interface Data


13

GND

Receiver Ground

1

14

Rx3p

Receiver Non-Inverted Data Output


15

Rx3n

Receiver Inverted Data Output


16

GND

Receiver Ground

1

17

Rx1p

Receiver Non-Inverted Data Output


18

Rx1n

Receiver Inverted Data Output


19

GND

Receiver Ground

1

20

GND

Receiver Ground

1

21

Rx2n

Receiver Inverted Data Output


22

Rx2p

Receiver Non-Inverted Data Output


23

GND

Receiver Ground

1

24

Rx4n

Receiver Inverted Data Output


25

Rx4p

Receiver Non-Inverted Data Output


26

GND

Receiver Ground

1

27

ModPrsl

Module Present


28

IntL

Interrupt


29

VccTx

3.3V power supply transmitter

2

30

Vcc1

3.3V power supply

2

31

LPMode

Low Power Mode,not connect


32

GND

Transmitter Ground

1

33

Tx3p

Transmitter Non-Inverted Data Input


34

Tx3n

Transmitter Inverted Data Output


35

GND

Transmitter Ground

1

36

Tx1p

Transmitter Non-Inverted Data Input



37

Tx1n

Transmitter Inverted Data Output


38

GND

Transmitter Ground

1


Notes:

1. GND is the symbol for signal and supply (power) common for the QSFP+ module. All are common within the QSFP+ module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane.

2. Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrently. Requirements defined for the host side of the Host Edge Card Connector are listed in Table 6. Recommended host board power supply filtering is shown in Figures 3 and 4. Vcc Rx Vcc1 and Vcc Tx may be internally connected within the QSFP+ Module in any combination. The connector pins are each rated for a maximum current of 500 mA.


image.png

Figure 1.Electrical Pin-out Details


Ordering information

 

 

Part. No


Specifications

 

Pack

Rate* (Gbps)

Po (dBm)

 

RX

Sen* (dBm)

Temp (℃)

Reach (m)

Pull tap

Color

 

DDM

HD-QSFP+/40G-SR4

QSFP+

4*10.3125

-7.6~2.4

PIN

<-9.5

0~+70

150

Beige

Y

*Note:

1.Measured with a PRBS 231-1 test pattern, @10.3125Gb/s, BER<1E-12. 2.Receiver sensitivity in OMA

Need Help? Contact Our Product Experts or Sales Team Today!

First Name*
Last Name*
Phone Number*
Company/Organization*
Email Address*
Country*
Comment or request*

Related Products

Latest News & Blog

Application and Advantages of 1×9 Optical Transceivers in Industrial Printing Systems
2025-08-05 Application and Advantages of 1×9 Optical Transceivers in Industrial Printing Systems

As industrial automation and smart manufacturing continue to evolve, communication systems within industrial printing equipment are shifting from traditional copper-based connections to more reliable fiber-optic solutions. Among various optical transmissi

Application of Optical Modules in Mesh Network Topology
2025-08-05 Application of Optical Modules in Mesh Network Topology

Consider employing a mesh network topology to meet your communication and data transmission needs. In this article, we will focus on the application of optical modules in mesh networks to help you better understand this critical technology. 1. High-Speed

Unlocking the Future of Connectivity with OTN Technology
2025-08-05 Unlocking the Future of Connectivity with OTN Technology

In todays rapidly evolving digital landscape, the need for reliable and efficient data transmission has never been more crucial. Enter Optical Transport Networks (OTN), a technology that is poised to revolutionize the way we connect and communicate. In th

Search

Search

Products

Service

Application

Application

Contact Us

Contact Us